Eurgle 9x Gear

Problems, experiences or just something to say about RC gear? Say it here.

Eurgle 9x Gear

Postby Schwab » Tue Aug 24, 2010 6:42 pm

Hello to all,
i hope that someone will help.
I have to set gear sw with one retract servo.

I go to AUX-CH ,set CH5 to GEAR. When i flip sw nothing hapends.
Servo is pluged in CH5,and if i set CH5 to pit-trim or hov-thr and move pit-trim or hov-thr servo is working.

Thanks to all.
User avatar
Schwab
 
Posts: 7
Joined: Tue May 04, 2010 7:04 am

Re: Eurgle 9x Gear

Postby Schwab » Tue Aug 24, 2010 7:36 pm

I set it up ,it works now ,just have to create new model.
Is it possibile to slow retract servo ,some curve adjustment ?


regards , Marko
User avatar
Schwab
 
Posts: 7
Joined: Tue May 04, 2010 7:04 am

Re: Eurgle 9x Gear

Postby RCModelReviews » Tue Aug 24, 2010 10:59 pm

No, although some radios like the JR9X have the ability to slow a servo -- even this only works if you're using a regular servo on your retracts because proper retract servos only have two positions - they're not proportional and their speed can't be controlled by the transmitter.
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Re: Eurgle 9x Gear

Postby Schwab » Wed Aug 25, 2010 12:39 pm

I will use rectract servo - BMS-136MG Retract Servo .


Can i set endpoints on radio for retract servo ?
Can i use http://www.hobbyking.com/hobbyking/stor ... oduct=8863 (Turnigy 3 Channel Servo Speed/Direction Regulator) ?
User avatar
Schwab
 
Posts: 7
Joined: Tue May 04, 2010 7:04 am

Re: Eurgle 9x Gear

Postby RCModelReviews » Wed Aug 25, 2010 10:42 pm

You can set endpoints for a regular (proportional) servo but if you're using a special retract servo they only have two positions that can't be changed by the radio and the speed also can't be changed.

What servos are you using?
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Re: Eurgle 9x Gear

Postby Schwab » Thu Aug 26, 2010 7:26 am

I will use BlueBird BMS-136MG Retract Servo- http://www.hobbyking.com/hobbyking/stor ... oduct=8770 .
If i can't do it on radio ,how to set end position when gear door is closed and position when it's opened?
You think that i can use http://www.hobbyking.com/hobbyking/stor ... oduct=8863 (Turnigy 3 Channel Servo Speed/Direction Regulator), to slow servo speed?
I will use retracts on CMP Zero 50.

thanks
User avatar
Schwab
 
Posts: 7
Joined: Tue May 04, 2010 7:04 am

Re: Eurgle 9x Gear

Postby RCModelReviews » Thu Aug 26, 2010 7:36 am

This is a dedicated retract servo so it will only turn to two positions and you can't change the speed at which it rotates.

Because of that, nothing you do with the transmitter will slow it down, nor will the servo-speed regulator have any effect.
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Re: Eurgle 9x Gear

Postby Schwab » Thu Aug 26, 2010 9:01 pm

Thanks Bruce !
User avatar
Schwab
 
Posts: 7
Joined: Tue May 04, 2010 7:04 am


Return to Radios and Servos

Who is online

Users browsing this forum: No registered users and 1 guest