Turnigy 9x v2

Here's an area where you can ask any kind of question about RC models and find a whole lot of useful information to help you get started.

Turnigy 9x v2

Postby aussiepaul » Thu Feb 21, 2013 1:24 am

Hi guys just wanted to start a new topic, i have the 9x vers 2 and need to find out how to setup flaps using the 3 position switch on a Multiplex funcub, have searched you tube but cant find one that is specific to just setting up flaps using the 3 position switch, if any has instructions on how to do this would be much appreciated.
aussiepaul
 
Posts: 1
Joined: Thu Feb 21, 2013 1:19 am

Re: Turnigy 9x v2

Postby cynr100 » Thu Feb 21, 2013 4:43 am

Hi Aussiepaul,

This may be of assistance, if you are using the stock 9x firmware.
http://9xforums.com/forum/viewtopic.php?f=37&t=1004
First, you must have one servo for each aileron and one channel for each servo, a 4ch Rx is not enough. I have not use the stock firmware for this, the er9x is much easier, how ever these condistions would still apply. :D
Not enough time in the day for all my crazy ideas, I'm not slow, I'm just pacing myself
User avatar
cynr100
 
Posts: 821
Joined: Wed Jan 25, 2012 7:37 am
Location: Cairns, Australia

Re: Turnigy 9x v2

Postby Chris916 » Tue Jun 18, 2013 3:14 pm

Not quite sure how to use this form yet but I have a turnigy 9X put a life battery in it 9.9 V 1800 wondering at what voltage should I recharge it and does this radio have a low-voltage alarm that will go off when it's too low so I don't crash my planes does anybody know anything about these radios
Chris916
 
Posts: 3
Joined: Tue Jun 18, 2013 2:21 pm

Re: Turnigy 9x v2

Postby BillGriffiths100 » Tue Jun 18, 2013 3:58 pm

The low voltage alarm goes off at 9 volts on the standard software.

Lithium iron phosphate (LiFePO4) battery:
Min. discharge voltage = 2.8 V
Working voltage = 3.0 ~ 3.3 V
Max. charge voltage = 3.6 V
So charge at 9 volts or thereabouts
Compromising with out of control government is like living with a lion, sooner or later the bloody thing will eat you .

You accept the tyranny of the state when it's not being applied to you, when it is: it's too late.
User avatar
BillGriffiths100
 
Posts: 553
Joined: Mon Sep 20, 2010 2:04 pm
Location: London UK

Re: Turnigy 9x v2

Postby Chris916 » Thu Jun 20, 2013 12:48 pm

Thanks for answering the last post you wouldn't happen to know what I charge 9.9 volt 1800 life battery at is it just like a Lipo 1.8?
Chris916
 
Posts: 3
Joined: Tue Jun 18, 2013 2:21 pm

Re: Turnigy 9x v2

Postby BillGriffiths100 » Thu Jun 20, 2013 2:45 pm

No it requires a lower cut off voltage see Bruces video about the turnigy charger he explains all:
see his video channels
http://www.youtube.com/watch?v=eX_Tuv6WOf8
Compromising with out of control government is like living with a lion, sooner or later the bloody thing will eat you .

You accept the tyranny of the state when it's not being applied to you, when it is: it's too late.
User avatar
BillGriffiths100
 
Posts: 553
Joined: Mon Sep 20, 2010 2:04 pm
Location: London UK


Return to For Beginners (if you're just getting started in RC)

Who is online

Users browsing this forum: No registered users and 4 guests

cron