I'm new to RC and bought an AXN

Here's an area where you can ask any kind of question about RC models and find a whole lot of useful information to help you get started.

Re: I'm new to RC and bought an AXN

Postby Hallmark » Thu May 10, 2012 9:17 am

cynr100 wrote:Yes mate it's all great fun, if it wasn't so windy today I could have videoed another crash :lol: :lol:


Ok so where is the video??? ;)
"I am prepared to meet my Maker. Whether my Maker is prepared for the great ordeal of meeting me is another matter." Winston Churchill
User avatar
Hallmark
 
Posts: 321
Joined: Mon Feb 13, 2012 2:21 am

Re: I'm new to RC and bought an AXN

Postby theeurofoxy » Thu May 10, 2012 12:27 pm

wow thats a pretty axn... yeah mark 1 is not going to be discarded, its actually going to be used as a test bed for my fpv winter project, i am taking all my fpv gear from my model car and putting in on the axn and gonna see how it feels,
the mark 2 axn will get its first flight on friday hopefully if the rain stay away...
theeurofoxy
 
Posts: 8
Joined: Fri Apr 20, 2012 9:33 pm

Re: I'm new to RC and bought an AXN

Postby cynr100 » Sat Jun 02, 2012 5:42 am

erricsimmons457 wrote:Hard to get along with the fact that your newly bought plane crashed.I still think RC planes are easy to fly than RC helicopters.I would be happy to
help you out in your search for the ones, I still want to make myself sure of what kind of stuff amazes you.You can try looking at Dirty Birdy .60 Sport/Pattern ARF,F-86 Sabre Micro EDF Tx-R,Gee Bee R-1 EP Rx-R,Citabria EP ARF,G-44 Widgeon Seaplane EP ARF,Cosmic Wind EP ARF.I hope this helps.


Annoying BOT post.

Anyway..................just 2 things I changed on my last rebuild that I did not point out. My receiver is the rather large FlySky unit and I had trouble mounting so that the canopy closed, I shaved out the rear bulk head down to the wing, lined it with doublesided tape. Now the transmitter forms part of the structure I removed and is flush enough to clear the canopy, I now have oodles of room so wire looms do not impede on the servos.

DSC08430.JPG
DSC08430.JPG (45.82 KiB) Viewed 3842 times
DSC08429.JPG
DSC08429.JPG (45.98 KiB) Viewed 3842 times


The original canopy clip was destroyed in the very first bunt, this has been replaced by a 20mm long bolt, 2 backing plates and a nut. The canopy now sits proud by 2mm and held in place by Mr Latex, provides easy access and extra cooling when I finally get going.
DSC08427.JPG
DSC08427.JPG (40.58 KiB) Viewed 3842 times


:D :D
Not enough time in the day for all my crazy ideas, I'm not slow, I'm just pacing myself
User avatar
cynr100
 
Posts: 821
Joined: Wed Jan 25, 2012 7:37 am
Location: Cairns, Australia

Re: I'm new to RC and bought an AXN

Postby Hallmark » Sun Jun 10, 2012 9:11 am

cynr100 wrote:Anyway..................just 2 things I changed on my last rebuild that I did not point out. My receiver is the rather large FlySky unit and I had trouble mounting so that the canopy closed, I shaved out the rear bulk head down to the wing, lined it with doublesided tape. Now the transmitter forms part of the structure I removed and is flush enough to clear the canopy, I now have oodles of room so wire looms do not impede on the servos.

The original canopy clip was destroyed in the very first bunt, this has been replaced by a 20mm long bolt, 2 backing plates and a nut. The canopy now sits proud by 2mm and held in place by Mr Latex, provides easy access and extra cooling when I finally get going.

:D :D


Nice work Dennis, I am hoping to see some flight footage soon as you're feeling better, SWMBO has time to accompany you (safety before fun), the AXN is ready to oblige you and Jupiter, Mars, Venus and Pluto are all in alignment lmao :lol: :lol:

Up Up and Away... ♫♫♪♫♪♪♫♪
"I am prepared to meet my Maker. Whether my Maker is prepared for the great ordeal of meeting me is another matter." Winston Churchill
User avatar
Hallmark
 
Posts: 321
Joined: Mon Feb 13, 2012 2:21 am

Re: I'm new to RC and bought an AXN

Postby joula » Mon Jun 18, 2012 8:15 am

Today I tried a new "airport". It was a really good flight in a windy condition but unfortunately the motor mount came out. But I was lucky because it came out only at the end of the flight.

See the full flight video here:
http://www.youtube.com/watch?v=nST-TQh_njs

The result can be seen on the below pic:
Attachments
IMG_2853.JPG
Motor mount and fuse
IMG_2853.JPG (169.16 KiB) Viewed 3796 times
joula
 
Posts: 13
Joined: Sat Mar 10, 2012 1:25 pm
Location: Hungary

Re: I'm new to RC and bought an AXN

Postby joula » Mon Jun 18, 2012 6:25 pm

AXN rescue :). It was a windy day and this was the second battery pack I flew with. After the hand launch the wind turned out the plane which flew behind the trees and I couldn't see it. Tried to recover but lost the control and decided to turn off the throttle and let's find it in the forest. And happy end, the plane was sitting on a low tree :). Lesson learnt, fly only on an open area.

See it on youtube:
http://www.youtube.com/watch?v=pq01UNPivgE
joula
 
Posts: 13
Joined: Sat Mar 10, 2012 1:25 pm
Location: Hungary

Re: I'm new to RC and bought an AXN

Postby cynr100 » Sun Jun 24, 2012 3:42 am

SO...................... :D ......................................I flew today, frustration got the better of me and I tossed my AXN accross the work paddock :o and I REALLY FLEW, controlled aileron turns 4 times around the paddock and a figure eight 8-) . Time for a touch and go, test my landing skill before it all goes pearshaped. Big mistake to downwind land :o ............... :lol: :lol: :lol:.
The aftermath, 20kph to 0 in 30mm, I couldn't be happier I FLEW.
DSC08446.JPG
DSC08446.JPG (52.43 KiB) Viewed 3765 times
DSC08447.JPG
DSC08447.JPG (54.97 KiB) Viewed 3765 times

DSC08449.JPG
DSC08449.JPG (48.28 KiB) Viewed 3765 times

I had my key chain cam record it all, so I thought :cry: :? :roll: alas it did not, now I have no proof, but I did fly honest, even squealed like a girl :P :lol:

Watch this space for repairs, hmmmmm... builders foam?.......hot water is NOT going to fix this.......time to learn how to hotwire foam ;)
Not enough time in the day for all my crazy ideas, I'm not slow, I'm just pacing myself
User avatar
cynr100
 
Posts: 821
Joined: Wed Jan 25, 2012 7:37 am
Location: Cairns, Australia

Re: I'm new to RC and bought an AXN

Postby Hallmark » Sun Jun 24, 2012 3:50 am

Nice work Dennis and that's only cosmetic damage, you'll sort it with hot glue, duct tape and a will to fly again.

Great to see you got it up ... Er... Um... You know what I mean. :lol:
"I am prepared to meet my Maker. Whether my Maker is prepared for the great ordeal of meeting me is another matter." Winston Churchill
User avatar
Hallmark
 
Posts: 321
Joined: Mon Feb 13, 2012 2:21 am

Re: I'm new to RC and bought an AXN

Postby BillGriffiths100 » Sun Jun 24, 2012 8:14 am

Watch this space for repairs, hmmmmm... builders foam?.......hot water is NOT going to fix this.......time to learn how to hotwire foam

Odourless cyano is a bit better cosmetically than hot glue it enables you to bring the pieces together with better joint closure, use pins to hold it together as it dries.
Any missing bits can be cut around to square up the edges the holes infilled with white insulation foam and sanded carefully to profile, a bit of patience and it will be good as well... then cover it with the wide clear parcel tape in sections to follow the contours, it will look surprisingly acceptable.
Compromising with out of control government is like living with a lion, sooner or later the bloody thing will eat you .

You accept the tyranny of the state when it's not being applied to you, when it is: it's too late.
User avatar
BillGriffiths100
 
Posts: 553
Joined: Mon Sep 20, 2010 2:04 pm
Location: London UK

Re: I'm new to RC and bought an AXN

Postby Hallmark » Sun Jun 24, 2012 8:21 am

BillGriffiths100 wrote:
Watch this space for repairs, hmmmmm... builders foam?.......hot water is NOT going to fix this.......time to learn how to hotwire foam

Odourless cyano is a bit better cosmetically than hot glue it enables you to bring the pieces together with better joint closure, use pins to hold it together as it dries.
Any missing bits can be cut around to square up the edges the holes infilled with white insulation foam and sanded carefully to profile, a bit of patience and it will be good as well... then cover it with the wide clear parcel tape in sections to follow the contours, it will look surprisingly acceptable.


Nice Bill thanks. Got a brand for the CA?
"I am prepared to meet my Maker. Whether my Maker is prepared for the great ordeal of meeting me is another matter." Winston Churchill
User avatar
Hallmark
 
Posts: 321
Joined: Mon Feb 13, 2012 2:21 am

PreviousNext

Return to For Beginners (if you're just getting started in RC)

Who is online

Users browsing this forum: No registered users and 4 guests

cron