Glue, glue, glue

Here's an area where you can ask any kind of question about RC models and find a whole lot of useful information to help you get started.

Glue, glue, glue

Postby Yellowirenut » Sat Oct 01, 2011 10:27 am

Very new to the hobby.
When i look threw the sellers web sites i see about 2 pages of just glue.
quick, fast, 15min, two part and right out of the bottle, thin, thick, foam safe

Is there a guide i can read up on what is best wear and when?
User avatar
Yellowirenut
 
Posts: 24
Joined: Wed Aug 31, 2011 11:07 am
Location: Fort Wayne, Indiana - USA

Re: Glue, glue, glue

Postby RCModelReviews » Sat Oct 01, 2011 11:59 pm

I should do a tutorial on glues I guess.

What do you want to glue?
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Re: Glue, glue, glue

Postby rogueqd » Sun Oct 02, 2011 1:41 am

I found Hobby Kings glue section quite useful. Just look through all the different glues and it says what each one can and can't glue, what's it's useful for etc.

A lot of it is just common sense. A foam safe glue is good for gluing foam, a 15 min epoxy takes about 15 mins before it's touch dry, thin glue is runnier than thick glue.
Also, just as important, is preparing the surfaces you want to glue. Do you need to clean them? Sand them? Warm them?

Like Bruce said "What do you want to glue?" Find out what the best glue is for your current project, then as you glue more things together you'll develop a broader knowledge about glues in general.
rogueqd
 
Posts: 234
Joined: Thu Mar 10, 2011 1:52 am
Location: Northern beaches, Sydney, Australia

Re: Glue, glue, glue

Postby quarry44 » Sun Oct 02, 2011 3:46 am

For gluing wood joints,such as balsa or spruce,aliphatic resin glue is relatively cheap,and sticks as good or better than balsa glue.I buy it in a quart bottle,lasts a long time.For firewalls,wing joiners,and other joints subject to stress 5 or 15 minute epoxy(2 part)is best.
I don't have much experience with foam,but again epoxy seems to stick ok.Epoxy IS heavy though.
Super glues are fine on most surfaces,but require neat joints,or baking soda filler.Thick super glues will fill minor gaps,but again a filler is useful.Hardwood doesn't usually take superglue,use epoxy or aliphatic here.
As you said,there's also foam-safe superglue,but I've never used it.
quarry44
 
Posts: 383
Joined: Fri Aug 19, 2011 6:58 am

Re: Glue, glue, glue

Postby Yellowirenut » Sun Oct 02, 2011 2:40 pm

What got me thinking about this mostly was watching the Rare Bear build on You Tubes. You mentioned brittle and a more pliable glue. I understood why but had never thought about it.
If i could donate or purchase the glue for you I would more than happy to, if you would do a guide. Not just to help me but others with the same thought.
User avatar
Yellowirenut
 
Posts: 24
Joined: Wed Aug 31, 2011 11:07 am
Location: Fort Wayne, Indiana - USA

Re: Glue, glue, glue

Postby RCModelReviews » Mon Oct 03, 2011 12:02 am

I'll probably do a quick guide that outlines which glues are best to use with which materials and then follow it up with a comparison of different brands.

Even within the different brands of CA I've noticed *big* differences. For example, the cheap HK CA is very slow to kick when used on most woods and plastics -- in fact, kicker is almost essential. Some other brands kick so quickly that they will actually give off visible vapors and create massive heat.

Epoxies vary from very fast (which also often means brittle) to quite slow in cure speed.

There are quite a few tips and tricks to be learned when using glue too -- so I'll share what I've learned over the last (almost) half century of model building.
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Re: Glue, glue, glue

Postby ergocentric » Mon Oct 03, 2011 3:24 pm

Never forget thick CA and kicker to glue your skin back together after a nasty cut.
unconcerned but not indifferent - MAN RAY
User avatar
ergocentric
 
Posts: 350
Joined: Sat Jun 05, 2010 9:45 pm
Location: small town, Ontario, Canada

Re: Glue, glue, glue

Postby ergocentric » Mon Oct 03, 2011 3:26 pm

One other thing, show us your hot glue guns, I need a new one that works better
unconcerned but not indifferent - MAN RAY
User avatar
ergocentric
 
Posts: 350
Joined: Sat Jun 05, 2010 9:45 pm
Location: small town, Ontario, Canada

Re: Glue, glue, glue

Postby kaptain_zero » Mon Oct 03, 2011 9:49 pm

While this site is directed at wood turners and it deals only with cyanoacrylate glues, there IS some good information, though it is not brand specific. If you are bored and looking for some reading, try this: http://goo.gl/FiMAE

As for hot glue guns.... I ordered one from DX (listed as 120w 110-220v) and while it works and is slimmer than my old version, it's no faster. I did notice that when I plug it into a 220v transformer I have, it heats up way faster and gets hotter, even with the thermostat setting staying the same. I'd suggest checking with nearby packaging material supply shops who should carry decent guns from 3M or some such supplier... Granted, the price is not for the faint of heart, so I intend to wait until both my guns die before I spring for a new one. Unfortunately, my Bostik gun is ~30 years old and shows no sign of giving up the ghost.... It's plenty good, just a bit clunky and I've lost the narrow nozzle for it.

Regards
Christian
"I'd like to live as a poor man with lots of money."
-- Pablo Picasso
User avatar
kaptain_zero
 
Posts: 197
Joined: Wed Mar 23, 2011 2:50 am
Location: Winnipeg, Canada

Re: Glue, glue, glue

Postby RCModelReviews » Tue Oct 04, 2011 12:48 am

Yeah, I bought a Bostik gun, thinking that a "brand name" would be good.

Nah... it's crap too!

Slow to heat up, dribbles too much and feels cheap.
RCModelReviews.com, just the facts.
User avatar
RCModelReviews
 
Posts: 2120
Joined: Tue May 04, 2010 3:40 am

Next

Return to For Beginners (if you're just getting started in RC)

Who is online

Users browsing this forum: No registered users and 10 guests

cron