So who's doing this reviewing then?
Well I've been building and flying or driving radio controlled models for over 40 years and during that time I like to think I've built up a reasonable amount of knowledge.
I'm also a qualified electronics engineer who has worked in radio frequency, analog, digital systems and software for more than three decades. In fact I designed and built my first RC set back in 1969.
For the past nine years I've also been involved in the design and manufacture of some rather sophisticated engine technology and UAV flight control systems.
So, chances are I've been there, done that and have a huge pile of tee shirts to prove it.
Right now I'm heavily into 3D flying and enjoy all aspects of the RC hobby. I may be old but I don't feel it.
In the Pipeline
Here's just a little bit of what's to come on this site...
RC explained: Demystifying terms such as PCM, PPM dual conversion, single conversion, full-range etc., this feature will explain it all.
Cheap Chinese Engines: Just how good are those cheap Chinese glow and gas engines that sell for half the price of their "brand-name" equivalent? I put several to the test.
Build your own radio gear?: Back in the old days, building your own RC gear was not uncommon and now the arrival of 2.4GHz has made it practical again.
Review: TowerPro/Hextronic MG995 servo
THE WORLD'S WORST SERVO?
You've probably seen these servos advertised on eBay and on the cyber-shelves of just about every Chinese RC box-drop web-store on the Net.
On paper, they sound fantastic.
Hi torque, good speed, low cost, digital amp and (depending on which piece of over-hyped advertising you read) they even have a coreless motor!
Based on these specifications I had great expectations for the MG995 servos so I bought a dozen or so at US$20 each and figured "how bad could they be?"
Well unfortunately the reality was far worse than anything I could have imagined.
These really are the worst servos I've ever seen - bar none!
Quality of construction
The MG995 looks like a fairly conventional standard-sized metal-geared servo from the outside.
A sturdy case and metal spline on the output shaft point to this being a good strong servo that might just live up to the manufacturer's claims.
Once you open up the case however, it becomes clear that these are not servos you should consider trusting any reasonable model to.
Inside you'll find a sorry lack of support where wires are joined to the amplifier circuit board and the motor.
This kid of unsupported wiring is an invitation for disaster. When used in any application where there's even a small amount of vibration, the constant flexing of the wire where it is soldered to the circuit board or motor will eventually cause a fracture.
Put these servos in your glow or gas-powered model and it's only a matter of time before they stop working due to broken wires.
Updated: 20 Sep 2012
Here's a blog that will keep you informed just what's going on behind the scenes at RC Model Reviews and also tells you a little more about myself.
23 Mar 2010
How come there's no compatibility between different brands of transmitters and receivers? Why can't you use a cheap Chinese receiver with your Futaba FASST radio?
4 Mar 2010
Since this has become a very frequently asked question, I've posted this simple guide to getting your product, or a product you're thinking of buying reviewed here at RCModelReviews
Useful information on what's inside your servos and how they work.
Important facts you should know about the oils that are used in our model engine fuels.
How well do five different 2.4GHz systems stack up when hit by interference? The answers are here, with more to come.
Yes it does work on model airplanes but there are some limitations involved with this bargain-basement radar speed gun.
These are possibly the world's worst servos, find out exactly why you should avoid these boat-anchors at any cost.
It's cheap but can it really stack up against other glow engines in the .90 market? Find out in this review.
How does this cheap 9-channel 2.4GHz radio system perform when compared to big-name systems that can cost two or three times as much? Have the Chinese finally developed a real contender with the iMax 9X?
Does all this 2.4GHz stuff have your head spinning?
I've done my best to demystify the whole subject so if you feel like a bit of learning, this is the stuff for you!
How can you tell when your engine needs new bearings? Who has the best prices and service on replacements? Just how do you change them? Get all that information and watch a great video tutorial anyone can follow.
The Chinese are now churning out a huge number of very reasonably priced no-name servos. But are they any good?
Nicad, NiMH, Li-Ion, LiPoly, LiFePO4, A123... the range of different battery types has never been greater. So how do they differ and what type should you be using?